Custom Search

Wednesday, February 18, 2009

MXR Zakk Wylde OD(ZW-44)


This is the MXR ZW-44 overdrive layout taken from Analogguru's schematic. I did not include Jack Orman's anti-LED pop this time but i use the original's LED switching instead. The pads labeled SWITCH is going to be connected in the 3PDT footswitch(if this will be used instead of DPDT). Please take note that the square pads of the diodes is the "+"(banded side or the cathode). Layout is verified.
Posted by at

12 comments:

  1. francesSeptember 7, 2010 at 3:01 AM

    hi
    first off, thanks for posting this!
    and then, is the PCB ready to transfert or does it need to be resized?
    and... a few questions about the pots, i guess the output pot is a 10K aas many others are, but which one is it? A, B, etc? and what does W mean for the tone pot?
    thanks, regards

    ReplyDelete
  2. AnonymousSeptember 16, 2010 at 7:55 AM

    I probe this layout and had poor gain and the vol it two low; it´s there perhaps I use a replace TL082 for the inubicable MC33718 in PERú? or whatever is?????

    ReplyDelete
  3. rapidriotSeptember 21, 2010 at 11:24 PM

    frances,

    Pot designations are according to the original units. The PCB is ready to transfer, yes. Just use a 10K -A(audio taper) for the volume/output.

    Anonymous,
    you might have a mistake in your build. Kindly double check it first. Any generic DUAL opamp will work.

    ReplyDelete
  4. AnonymousSeptember 25, 2010 at 12:44 PM

    I also have same problem, low gain low level. I used 4558 chip. Is this layout really verified?

    ReplyDelete
  5. rapidriotSeptember 26, 2010 at 8:09 PM

    Let me ask, what transistor were you using for this one?.

    By the way, the capacitor above the GND and IN pads was mistakenly labeled 47uF, the correct value should be 4.7µF(4µ7).

    This layout is based on this schematic: http://analogguru.an.ohost.de/193/schematics/Mxr_ZakkWylde.gif

    Transistor calls for MPSA14, it's a high gain DARLINGTON type transistor!. You could probably use MPSA13 on this one.

    ReplyDelete
  6. AnonymousSeptember 27, 2010 at 4:32 AM

    I used MPSA13. Maybe I should make new pcb and try again.

    ReplyDelete
  7. AnonymousOctober 1, 2010 at 2:52 PM

    what about the resistor 1M (below the IN on the PCB) - this resistor is not included in the schematic terefore I am not sure it should be there or not ??

    And also, what pots I should use ? are all of them linear ?
    thanks

    ReplyDelete
  8. ArtApril 11, 2011 at 1:13 AM

    Hi! Is here someone that have built this board with some good result?

    ReplyDelete
  9. UnknownApril 17, 2011 at 8:04 AM

    This comment has been removed by the author.

    ReplyDelete
  10. AnonymousApril 17, 2011 at 8:06 AM

    http://www.megaupload.com/?d=ITOYV4NO
    PCB in PDF file.
    by UH!Bom

    ReplyDelete
  11. lahooMarch 10, 2012 at 7:12 AM

    Has anybody got resized and ready to print PDF version of layout?

    ReplyDelete
  12. AnonymousNovember 25, 2024 at 3:44 AM

    Cool and I have a super present: What Does A Full House Renovation Cost house renovation training

    ReplyDelete

Subscribe to: Post Comments (Atom)